Extruder Calibration - meine derzeitige Firmware Settings

Send: N1494 M205*28
Recv: ok 1494
Recv: EPR:0 1028 0 Language
Recv: EPR:2 75 115200 Baudrate
Recv: EPR:3 129 1905.765 Filament printed [m]
Send: N1495 G1 X92.632 Y96.122 E19.46257*99
Recv: EPR:2 125 1415005 Printer active [s]
Recv: EPR:2 79 0 Max. inactive time [ms,0=off]
Recv: EPR:2 83 360000 Stop stepper after inactivity [ms,0=off]
Recv: EPR:3 3 100.0000 X-axis steps per mm
Recv: EPR:3 7 100.0000 Y-axis steps per mm
Recv: EPR:3 11 400.0000 Z-axis steps per mm
Recv: EPR:3 15 400.000 X-axis max. feedrate [mm/s]
Recv: EPR:3 19 400.000 Y-axis max. feedrate [mm/s]
Recv: EPR:3 23 4.000 Z-axis max. feedrate [mm/s]
Recv: EPR:3 27 100.000 X-axis homing feedrate [mm/s]
Recv: EPR:3 31 100.000 Y-axis homing feedrate [mm/s]
Recv: EPR:3 35 2.000 Z-axis homing feedrate [mm/s]
Recv: EPR:3 39 8.000 Max. jerk [mm/s]
Recv: EPR:3 47 1.414 Max. Z-jerk [mm/s]
Recv: EPR:3 133 -45.000 X min pos [mm]
Recv: EPR:3 137 -5.000 Y min pos [mm]
Recv: EPR:3 141 0.000 Z min pos [mm]
Recv: EPR:3 145 265.000 X max length [mm]
Recv: EPR:3 149 230.000 Y max length [mm]
Recv: EPR:3 153 240.000 Z max length [mm]
Recv: EPR:3 1056 0.000 Park position X [mm]
Recv: EPR:3 1060 10.000 Park position Y [mm]
Recv: EPR:3 1064 10.000 Park position Z raise [mm]
Recv: EPR:3 51 400.000 X-axis acceleration [mm/s^2]
Recv: EPR:3 55 400.000 Y-axis acceleration [mm/s^2]
Recv: EPR:3 59 400.000 Z-axis acceleration [mm/s^2]
Recv: EPR:3 63 400.000 X-axis travel acceleration [mm/s^2]
Recv: EPR:3 67 400.000 Y-axis travel acceleration [mm/s^2]
Recv: EPR:3 71 400.000 Z-axis travel acceleration [mm/s^2]
Recv: EPR:3 1032 50.000 Acceleration factor at top [%,100=like bottom]
Recv: EPR:3 1024 0.000 Coating thickness [mm]
Recv: EPR:1 1048 55 Bed Preheat temp. [�C]
Recv: EPR:0 106 0 Bed Heat Manager [0-3]
Recv: EPR:0 107 255 Bed PID drive max
Recv: EPR:0 124 80 Bed PID drive min
Recv: EPR:3 108 196.000 Bed PID P-gain
Recv: EPR:3 112 33.000 Bed PID I-gain
Recv: EPR:3 116 290.000 Bed PID D-gain
Recv: EPR:0 120 255 Bed PID max value [0-255]
Recv: EPR:0 1020 0 Enable retraction conversion [0/1]
Recv: EPR:3 992 3.000 Retraction length [mm]
Recv: EPR:3 1000 40.000 Retraction speed [mm/s]
Recv: EPR:3 1004 0.000 Retraction z-lift [mm]
Recv: EPR:3 1008 0.000 Extra extrusion on undo retract [mm]
Recv: EPR:3 1016 20.000 Retraction undo speed
Recv: EPR:3 200 132.000 Extr.1 steps per mm
Recv: EPR:3 204 3.000 Extr.1 max. feedrate [mm/s]
Recv: EPR:3 208 20.000 Extr.1 start feedrate [mm/s]
Recv: EPR:3 212 5000.000 Extr.1 acceleration [mm/s^2]
Recv: EPR:1 294 190 Extr.1 Preheat temp. [�C]
Recv: EPR:0 216 3 Extr.1 heat manager [0-3]
Recv: EPR:0 217 230 Extr.1 PID drive max
Recv: EPR:0 245 40 Extr.1 PID drive min
Recv: EPR:3 218 7.0000 Extr.1 PID P-gain/dead-time
Recv: EPR:3 222 2.0000 Extr.1 PID I-gain
Recv: EPR:3 226 40.0000 Extr.1 PID D-gain
Recv: EPR:0 230 255 Extr.1 PID max value [0-255]
Recv: EPR:2 231 0 Extr.1 X-offset [steps]
Recv: EPR:2 235 0 Extr.1 Y-offset [steps]
Recv: EPR:2 290 0 Extr.1 Z-offset [steps]
Recv: EPR:1 239 1 Extr.1 temp. stabilize time [s]
Recv: EPR:1 250 150 Extr.1 temp. for retraction when heating [C]
Recv: EPR:1 252 0 Extr.1 distance to retract when heating [mm]
Recv: EPR:0 254 255 Extr.1 extruder cooler speed [0-255]